How do you neck size only?
Is it safe to assume that you just limit the travel on your press?
neck sizing
-
Bill K
- Senior Member
- Posts: 2324
- Joined: Tue Jan 18, 2011 10:00 am
- .204 Ruger Guns: also now, a Savage switch bull barrel in 204R. 23 inch SS
- Location: Lake Forest, Ca.
Re: neck sizing
You either back off your FL die to just size the portion of the neck you want sized, or you buy a neck/bushing die, that just sizes the neck area. 
-
skipper
- Moderator
- Posts: 1404
- Joined: Thu Feb 09, 2006 3:32 am
- .204 Ruger Guns: Remington XR 100, Custom build Lilja/Panda/Shehane/Jewell
- Location: Cypress, TX
Re: neck sizing
I would never admit to cutting the body off a bushing neck sizing die just so I didn't work the body. 
Where's my Dremel drill?? Remember to leave the sizing bushing loose enough to self center on the neck. Just size half the neck.
Where's my Dremel drill?? Remember to leave the sizing bushing loose enough to self center on the neck. Just size half the neck.
Hold 'em & Squeeze 'em-
MZ5
- Senior Member
- Posts: 106
- Joined: Sat Oct 13, 2007 2:57 pm
- .204 Ruger Guns: Ruger M77 Hawkeye Predator
- Location: Arizona, USA
Re: neck sizing
I find a collet-type neck-sizing die the best option for me to neck-only re-size brass. Lee makes a very affordable one that works extremely well.
-
Rick in Oregon
- Moderator
- Posts: 4942
- Joined: Thu Dec 01, 2005 4:20 pm
- .204 Ruger Guns: Sako 75V, Cooper MTV, Kimber 84M, Cust M700 11 Twist
- Location: High Desert of Central Oregon
- Contact:
Re: neck sizing
Lots of opinions on this, lots of choices.
For me, it's a Redding Bushing Neck Die (does not touch the body of the case, only the neck), with the correct size bushing. This combination has given me TIR readings as low as 'zero', usually right at .001" or less.
With great dies from various makers just for this purpose, get a neck die and do it properly.
For me, it's a Redding Bushing Neck Die (does not touch the body of the case, only the neck), with the correct size bushing. This combination has given me TIR readings as low as 'zero', usually right at .001" or less.
With great dies from various makers just for this purpose, get a neck die and do it properly.
Semper Fortis
Rick in Oregon
NRA Life/OHA/VHA/VVA
Oregon, East of the Cascades - Where Common Sense Still Prevails
Rick in Oregon
NRA Life/OHA/VHA/VVA
Oregon, East of the Cascades - Where Common Sense Still Prevails
-
Rick in Oregon
- Moderator
- Posts: 4942
- Joined: Thu Dec 01, 2005 4:20 pm
- .204 Ruger Guns: Sako 75V, Cooper MTV, Kimber 84M, Cust M700 11 Twist
- Location: High Desert of Central Oregon
- Contact:
Re: neck sizing
Lots of opinions on this, lots of choices.
For me, it's a Redding Bushing Neck Die (does not touch the body of the case, only the neck), with the correct size bushing. This combination has given me TIR readings as low as 'zero', usually right at .001" or less. And as Skipper mentioned, always leave the lock nut loose on the bushing, leaving it free to self-center on the case neck to avoid drawing it off center with a locked bushing, that never truly locks "true" if locked down.
With great dies from various makers just for this purpose, get a neck die and do it properly.
For me, it's a Redding Bushing Neck Die (does not touch the body of the case, only the neck), with the correct size bushing. This combination has given me TIR readings as low as 'zero', usually right at .001" or less. And as Skipper mentioned, always leave the lock nut loose on the bushing, leaving it free to self-center on the case neck to avoid drawing it off center with a locked bushing, that never truly locks "true" if locked down.
With great dies from various makers just for this purpose, get a neck die and do it properly.
Semper Fortis
Rick in Oregon
NRA Life/OHA/VHA/VVA
Oregon, East of the Cascades - Where Common Sense Still Prevails
Rick in Oregon
NRA Life/OHA/VHA/VVA
Oregon, East of the Cascades - Where Common Sense Still Prevails