CZ 452 17 HMR

[Sidewinderwa]

I bought a new CZ 452 American in 17 HMR. I always clean new guns up before shooting them. The cleaning patches were all rust filled. I used Butch's Bore Shine, Kroil and Blue Wonder and the patches are still coming out rust colored. I am sending in a letter with patches and registration paperwork now. Has anyone else had this problem with CZ? I have another CZ rifle in 223 and did not have any rust. What a disappointment. I hope they have good customer support.

[RAMOS]

I have no first hand experience with this. However, I have read about it a few times. Seems that it turns out to be be the packing grease they use and it does indeed LOOK like rust. Also, it takes a lot of effort to get it all out of the rifle. Hopefully that is what you have going on.

[futuretrades]

About the only thing I will add is, I have my issues with my CZ 452 American, chambered in 17 HMR!:headache:

[Sidewinderwa]

Why would ANY rifle company make a rust colored product, especially if it goes in a barrel? Blue Wonder is my go to product when other products are not working.
Futuretrades, what are your issues with the 452? Should I ask for a different rifle to replace it???

[futuretrades]

Futuretrades, what are your issues with the 452? Should I ask for a different rifle to replace it???

My biggest issue is feeding issues from the mag into the chamber. When shooting, I always have to keep in mind to push the bolt forward using my thumb, or I get a jam. Do a search on this site, and you will find other CZ owners with the same issues. I have been shooting bolt rifles for most of my 59 yrs and have never, ever had this problem with the way I operate the bolt. Also, I really hate the clip in this rifle. I sold my model 77 Ruger all weather in 17HMR to finance my 204. I never had any issues with that rifle, no matter how excited I got, or how I manipulated the bolt. As far as I am concerned, that is the way every rifle should operate. And I was more than happy with the clip set up.
If you decide on another rifle, that is your choice. These are only my pet peeves with this rifle. I guess its like a Chevy or Ford thing, always pro and con, and everyone is entitled to their opinion. If and when I can get what I would ask for the rifle, I just may sell it.

[204_au]

Futuretrades, what are your issues with the 452? Should I ask for a different rifle to replace it???

My biggest issue is feeding issues from the mag into the chamber. When shooting, I always have to keep in mind to push the bolt forward using my thumb, or I get a jam. Do a search on this site, and you will find other CZ owners with the same issues.

Try adjusting the tabs in the top end of the magazine. I put thousands of rounds through my CZ 452 varmint 17HMR and never had feeding issues, until one day dropping the magazine on it's end which slightly bent the two tabs inward. After that, it would occasionally jam until I re-adjusted the tabs ever so slightly outward, and the rifle began feeding smoothly again.

[Sidewinderwa]

I know that there are higher capacity magazines for the 452 but could not find any for sale. Anyone know who has them for sale?

[RUD]

I have two CZ's and the grease is a pain to remove. The people on RFC.COM suggested using W-40 or Goo Gone and they both seem to work on removing that crap in the barrel. I haven't had any other issues as of yet to complain about the CZ's. You may want to check CZ Custom Shop on the net for the magazines. The CZ forum on RFC.COM has a wealth of info. for the CZ owner, they have all the answers it seems. Good luck on your new purchase! Rudy

[Sidewinderwa]

RUD, thanks for the link, I had forgotten all about that site. I will check it out for more info.

[jrwoitalla]

What about just putting some lead down the tube then cleaning it? Seems to me the heat and pressure of shooting it might blast that crap right out the end of the barrel and/or burn it up. After that it might clean up quite easily. Then again, I could be wrong. My 452 17hmr wouldn't group very well until it had a couple hundred rounds down the tube, that might be why.
I've had my issues with CZ as well. My 452 has a bad scope rail-it's not even close to square, the windage is adjusted all the way over to the right just to get it centered. My 527 in 204r has the same feeding problem mentioned above, it jams up unless I push it in with my thumb. Nevertheless, both guns are so accurate and otherwise well made, that I've all but forgotten about those little warts. That's why I'm in the market for another 527 in 221 fireball and a 75b in 9mm.

[futuretrades]

Good luck with your new CZ purchase. All I know is that I will never purchase a CZ again as long as I am buying new firearms!