cfe-223 powder

Share information about reloading the 204 Ruger.
truckerwalt
Junior Member
Posts: 88
Joined: Mon Jan 23, 2012 10:59 am
.204 Ruger Guns: RUGER MK II/SAVAGE MOD. 12

cfe-223 powder

Post by truckerwalt »

i have a savage model 12 with a monarch 5.5 x 16.5 x 44 scope. i have spent some time trying to come up with a good load and have finally come up with a real tack driver. i use 30.6 gr. CFE-223 powder--35 gr. berger bullets and fed gm205m primers. my last group measured .38" with 5 shots into 3 holes at 100 yards. i know others probably think that is not that great but it is for me.

i also have a rem. 700 sps varmint in .223 rem. with 27.3 gr. of CFE-223 and rem. 7.5 primers shooting 55 gr. hornady sx seated to the channelure and it gives awsome groups. my rifles no longer builds copper in the barrel. usually 4 wet patches and it is clean. i love my CFE-223 powder.
User avatar
Darkker
Senior Member
Posts: 225
Joined: Tue Jan 03, 2012 3:35 pm
.204 Ruger Guns: Ruger Predator
Location: SE Washington

Re: cfe-223 powder

Post by Darkker »

Glad to hear you like it! A friend fooled around with it in the non-canister version, SMP-842 and liked it also.
I'm a firm believer in the theory that if it bleeds, I can kill it.
User avatar
Tokimini
Senior Member
Posts: 428
Joined: Wed Dec 08, 2010 8:21 am
.204 Ruger Guns: Remington 700 SPS with a Shilen barrel
Location: Victor, NY

Re: cfe-223 powder

Post by Tokimini »

CFE has gotten to be my favorite powder, and I think a 5 shot .38" group at 100yds would be good for anyone.
Bill K
Senior Member
Posts: 2324
Joined: Tue Jan 18, 2011 10:00 am
.204 Ruger Guns: also now, a Savage switch bull barrel in 204R. 23 inch SS
Location: Lake Forest, Ca.

Re: cfe-223 powder

Post by Bill K »

It is becoming my #1 choice in the 223 and 204. Tried to work up a load in the 20VT (no load data in manuals) I had fine accuracy, but could not get over 3100 fps and the case was full. So on the 20VT back to the other powders, but for the other two, it will most likely be my go to powder. I am going to try it in the 22-250 next. Bill K
tpcollins
Senior Member
Posts: 108
Joined: Mon Mar 21, 2011 6:05 pm
.204 Ruger Guns: Tikka T3 Lite

Re: cfe-223 powder

Post by tpcollins »

How does the CFE-223 compare to IMR-8208-XBR? I've tried several powders and the 8208 works best in my .204 & .223. I'm almost out and was trying to decide on more 8208 or trying the CFE-223.
Bill K
Senior Member
Posts: 2324
Joined: Tue Jan 18, 2011 10:00 am
.204 Ruger Guns: also now, a Savage switch bull barrel in 204R. 23 inch SS
Location: Lake Forest, Ca.

Re: cfe-223 powder

Post by Bill K »

For me anyway, I prefer the CFE over 8208, for two reasons at this point. First it meters so much nicer. Second it gives me a little better accuracy and cleans up faster. That are my reasons at this point. Bill K
User avatar
DoubleUp
Senior Member
Posts: 146
Joined: Tue Dec 21, 2010 5:36 pm
.204 Ruger Guns: 204 Ruger

Re: cfe-223 powder

Post by DoubleUp »

Bill K, I've tried cfe 223 in 204, 223, 22-250, and 243. I've had by far the best results in the 22-250 with great velocity at minimum charge (50 g bullets, 3,900 fps) and super accuracy. Also I've started breaking in new barrels with it since it does cut down on the copper effect in new factory barrels. It might not make any difference with custom barrels.
User avatar
Tokimini
Senior Member
Posts: 428
Joined: Wed Dec 08, 2010 8:21 am
.204 Ruger Guns: Remington 700 SPS with a Shilen barrel
Location: Victor, NY

Re: cfe-223 powder

Post by Tokimini »

I've found that the CFE223 is a bit more accurate than 8208XBR in my 204 Remmy 700 and like Bill mentioned it meters much better. I ran out of 8208XBR a few weeks ago and have no plans to get anymore. I'm just going to use CFE223 and good old Reloder 10X from now on.
User avatar
Bodei
Senior Member
Posts: 442
Joined: Tue Jan 31, 2012 9:23 pm
.204 Ruger Guns: Howa Mod 1500 24" BBL .204R; Cooper M21 20 VT; CZ 527 17HH
Location: Reno, NV
Contact:

Re: cfe-223 powder

Post by Bodei »

I plan on using this powder when I run out of H335. Can anyone post any load data?
Image
K = ½mv2
User avatar
DoubleUp
Senior Member
Posts: 146
Joined: Tue Dec 21, 2010 5:36 pm
.204 Ruger Guns: 204 Ruger

Re: cfe-223 powder

Post by DoubleUp »

Best data will probably be found here since the powder is new and hasn't been out long enough to be in many printed load manuals. From what I've seen in my 204 the velocity runs pretty close to the published data using 32, 35, and 40's. Actually I shoot 39 sbk's instead of 40's, but runs about the same. No signs of pressure at max loads in 204 for my rifle.

http://data.hodgdon.com/cartridge_load.asp
Bill K
Senior Member
Posts: 2324
Joined: Tue Jan 18, 2011 10:00 am
.204 Ruger Guns: also now, a Savage switch bull barrel in 204R. 23 inch SS
Location: Lake Forest, Ca.

Re: cfe-223 powder

Post by Bill K »

Bodei. I have found that in my loads, every one of them seems to settle in around .3-.5 grains under the max listed load. So far in the 223 and 204 anyway.. I would start around one grain under max and go from there. Check out Hodgdon's Data center, they list CFE now in the charts. :) Bill K
fireman204
New Member
Posts: 12
Joined: Sun Feb 20, 2011 10:31 pm
.204 Ruger Guns: rem 700vls ,ar15
Location: ks.

Re: cfe-223 powder

Post by fireman204 »

has anyone had any accuracy changes with cfe223 when the temp goes from the 80s to into the 100s . I went from .5 groups to 1in. groups when the temp went up
Bill K
Senior Member
Posts: 2324
Joined: Tue Jan 18, 2011 10:00 am
.204 Ruger Guns: also now, a Savage switch bull barrel in 204R. 23 inch SS
Location: Lake Forest, Ca.

Re: cfe-223 powder

Post by Bill K »

I have not noticed any change in the temp areas of 75-95 degrees.. Am interested, later this fall/winter, when I varmint hunt more (rabbits/coyote) and the temps go down on a average from 40 above to 5 below. Time will tell on that one. Bill K
Post Reply