I have been tip toeing around the idea of reloading for my .204, looking at the sea of equipment out there and never really knowing where to start. Yesterday a fellow archer decided to retire his stuff and I snapped it up, I know absolutely nothing about reloading but have been doing some reading. I hope the stuff I bought is decent, I plan to ditch what I don't need and stick to reloading my only center fire, my .204.
Here is a list of what I bought, paid just over $200 for the lot.
What am I going to need now?
rcbs cast bullet manual
lyman 47th reloading manual
lyman 45th reloading manual
sierra handgun reloading manual - 3rd edition
cartridges of the world manual
rcbs 45/70 3 die set
assorted resizing lubricants
rcbs uniflow powder measure
lee auto disc powder measure - 2 of these
20 ++ shellholders
set of trim collets/pilots - to go with the case trimmer
case lube pad
powder dribbler
assorted loading blocks
rcbs pneaumatic bullet puller
at least 5 auto turrets of the lee presses
assorted bullet and case lubes
rcbs 505 scale
case brushes and assorted "stuff"
32-40 antique hand die
auto index ratchets
lee auto index press (2 of these)
rcbs case trimmer
rcbs O frame press
45 cal neck expander
30 cal neck expander
22 cal neck expander
powder measure table bracket to fit the unflow powder measure
38-357 carbide die set
assorted brass new and used (all types)
lyman check scale set
assorted cartridge cases
redding 762x39 die set
redding 762x39 neck expander/resizer/shell holder set
"if there is anything else reloading wise kicking around that goes too. !.. "
I am going to need some help soon..
-
- Senior Member
- Posts: 463
- Joined: Tue Nov 07, 2006 7:56 pm
- .204 Ruger Guns: ruger 77VT and ruger mkII Ultralite
- Location: Deer Trail, CO
Re: I am going to need some help soon..
You'll need a set of .204 dies. The 45-70 ones won't cut it........grin
- Glen
- Moderator
- Posts: 1741
- Joined: Sun Feb 06, 2005 9:22 pm
- .204 Ruger Guns: Rem700ADL
- Location: New Philadelphia, Ohio
- Contact:
Re: I am going to need some help soon..
Did you get the press itself or just the turrets?
Purdy good deal ya got there!!![Mr. Green :mrgreen:](./images/smilies/icon_mrgreen.gif)
Purdy good deal ya got there!!
![Mr. Green :mrgreen:](./images/smilies/icon_mrgreen.gif)
Friends Are Friends By Nature.
RIP Russ,Blaine, & Darrell!!
I don't like repeat offenders. I like DEAD offenders!!
Ted Nugent
Isn't there a minimum age for grampas??
^^^^^^
Audrey Renae told me "No there isn't"!!
Glen
RIP Russ,Blaine, & Darrell!!
I don't like repeat offenders. I like DEAD offenders!!
Ted Nugent
Isn't there a minimum age for grampas??
^^^^^^
Audrey Renae told me "No there isn't"!!
Glen
-
- Junior Member
- Posts: 92
- Joined: Tue Jan 15, 2008 4:27 pm
- .204 Ruger Guns: Tikka Varmint
- Location: Ontario, Canada
Re: I am going to need some help soon..
I had to go over that list Glen, it says a RCBS O frame press.. Now, I have no idea what any of this is, I am learning slowly though. A few buddies said it was a good deal so I jumped on it. I am thinking I may need a 45-70 so I can use the stuff.
I am having buyers remorse, I bought this stuff thinking it would get me started, minus of course the .204 dedicated stuff I need.
![Very Happy :D](./images/smilies/icon_biggrin.gif)
I am having buyers remorse, I bought this stuff thinking it would get me started, minus of course the .204 dedicated stuff I need.
-
- Senior Member
- Posts: 227
- Joined: Sun Feb 10, 2008 5:01 pm
- .204 Ruger Guns: Remington 700 VTR
- Location: Minnesota
Re: I am going to need some help soon..
You might want a dedicated 20 cal powder funnel and a set of calipers. You might also want to consider flash hole deburring and primer pocket uniformer tools. Here's a nice powder funnel.
http://www.sinclairintl.com/cgi-bin/cat ... type=store
Otherwise you made a good deal. Good luck and have fun
http://www.sinclairintl.com/cgi-bin/cat ... type=store
Otherwise you made a good deal. Good luck and have fun
- Glen
- Moderator
- Posts: 1741
- Joined: Sun Feb 06, 2005 9:22 pm
- .204 Ruger Guns: Rem700ADL
- Location: New Philadelphia, Ohio
- Contact:
Re: I am going to need some help soon..
![eew :eew:](./images/smilies/eew.gif)
![lol :lol:](./images/smilies/lol.gif)
![lol :lol:](./images/smilies/lol.gif)
Friends Are Friends By Nature.
RIP Russ,Blaine, & Darrell!!
I don't like repeat offenders. I like DEAD offenders!!
Ted Nugent
Isn't there a minimum age for grampas??
^^^^^^
Audrey Renae told me "No there isn't"!!
Glen
RIP Russ,Blaine, & Darrell!!
I don't like repeat offenders. I like DEAD offenders!!
Ted Nugent
Isn't there a minimum age for grampas??
^^^^^^
Audrey Renae told me "No there isn't"!!
Glen
-
- Junior Member
- Posts: 97
- Joined: Thu Jul 03, 2008 1:50 pm
- .204 Ruger Guns: Ruger No. 1
Re: I am going to need some help soon..
A new realoading manual. I lke the Hornady, it has a good introduction for the novice in the front. Most powder and bullet companies have relaoding data online or available through their online tech support for their powders and bullets.
A set of 204 dies. I got a Redding "Deluxe" three die set, and generally neck size only for my Ruger No. 1. If you have a semiauto, you will need to full length resize every time, so don't spend the money for a neck sizer die.
I have an RCBS competition seater die and unlike some others haven't had any problems with it, that weren't me. There are some people who have issues with the bullet concentricity using it. I did, have a problem the first time I used it, because if I didn't pay attention the bullet wouldn't drop all the way into the guide, and wouldn't seat true. Once I figured that out, I haven't had any concentricity issues, that I have been able to measure. I like it becuase it lets you load the bullet from the top. I punched a hole in my finger once relaoding for my Brother's .17 Remington, by not paying attention and catching the side of my finger in the case mouth, while trying to hold the little bullet, and work the ram to seat it.
A set of 204 dies. I got a Redding "Deluxe" three die set, and generally neck size only for my Ruger No. 1. If you have a semiauto, you will need to full length resize every time, so don't spend the money for a neck sizer die.
I have an RCBS competition seater die and unlike some others haven't had any problems with it, that weren't me. There are some people who have issues with the bullet concentricity using it. I did, have a problem the first time I used it, because if I didn't pay attention the bullet wouldn't drop all the way into the guide, and wouldn't seat true. Once I figured that out, I haven't had any concentricity issues, that I have been able to measure. I like it becuase it lets you load the bullet from the top. I punched a hole in my finger once relaoding for my Brother's .17 Remington, by not paying attention and catching the side of my finger in the case mouth, while trying to hold the little bullet, and work the ram to seat it.
-
- Senior Member
- Posts: 398
- Joined: Sat Jan 28, 2006 9:42 pm
- .204 Ruger Guns: Savage mod. 116 and Custom .204 AR
- Location: East Central MO
Re: I am going to need some help soon..
Since you only plan to load for a .204, these are the things I see on the list that you don't need... and if you sold them, they might bring enough to buy what you do need, plus some extra...
rcbs cast bullet manual
cartridges of the world manual
rcbs 45/70 3 die set
assorted resizing lubricants
lee auto disc powder measure - 2 of these
20 ++ shellholders
assorted loading blocks
at least 5 auto turrets of the lee presses
assorted bullet and case lubes
32-40 antique hand die
auto index ratchets
lee auto index press (2 of these)
45 cal neck expander
30 cal neck expander
22 cal neck expander
38-357 carbide die set
assorted brass new and used (all types)
assorted cartridge cases
redding 762x39 die set
redding 762x39 neck expander/resizer/shell holder
You don't indicate what model of the Lee Auto Index Presses you have. If they are the Lee 1000 (takes a 3 or 4 die holder), then you might be able to get it to work for reloading the .204. I have one and have never gotten the powder system to work with the bottle neck cases without crushing them.
The 'assorted brass' would certainly be worth cleaning, classifying, and selling....
A good set of dies for your .204 won't run that much and you should be able to turn enough money from the stuff you don't need to buy the best on the market..![chin :chin:](./images/smilies/chin.gif)
rcbs cast bullet manual
cartridges of the world manual
rcbs 45/70 3 die set
assorted resizing lubricants
lee auto disc powder measure - 2 of these
20 ++ shellholders
assorted loading blocks
at least 5 auto turrets of the lee presses
assorted bullet and case lubes
32-40 antique hand die
auto index ratchets
lee auto index press (2 of these)
45 cal neck expander
30 cal neck expander
22 cal neck expander
38-357 carbide die set
assorted brass new and used (all types)
assorted cartridge cases
redding 762x39 die set
redding 762x39 neck expander/resizer/shell holder
You don't indicate what model of the Lee Auto Index Presses you have. If they are the Lee 1000 (takes a 3 or 4 die holder), then you might be able to get it to work for reloading the .204. I have one and have never gotten the powder system to work with the bottle neck cases without crushing them.
The 'assorted brass' would certainly be worth cleaning, classifying, and selling....
A good set of dies for your .204 won't run that much and you should be able to turn enough money from the stuff you don't need to buy the best on the market..
![chin :chin:](./images/smilies/chin.gif)
AR
![Image](http://i82.photobucket.com/albums/j261/OldTurtleFiles/Miscellaneous%20Projects/Range%20Pics/1st20In20Class.jpg)
Factory/Factory
![Image](http://i82.photobucket.com/albums/j261/OldTurtleFiles/Miscellaneous%20Projects/Range%20Pics/3rd20In20Class.jpg)
![Image](http://i82.photobucket.com/albums/j261/OldTurtleFiles/Miscellaneous%20Projects/Range%20Pics/1st20In20Class.jpg)
Factory/Factory
![Image](http://i82.photobucket.com/albums/j261/OldTurtleFiles/Miscellaneous%20Projects/Range%20Pics/3rd20In20Class.jpg)
-
- Junior Member
- Posts: 51
- Joined: Sat May 17, 2008 5:14 pm
- .204 Ruger Guns: Savage 12 Varminter low profile
- Location: Cody, Wyoming
Re: I am going to need some help soon..
Unfortunately you can't use the Lee Pro Auto Disc powder measure with the 204 caliber without modifying your program a bitIf they are the Lee 1000 (takes a 3 or 4 die holder), then you might be able to get it to work for reloading the .204.
![Smile :)](./images/smilies/icon_smile.gif)
A couple years ago I upgraded to the newer Lee Classic (I think that's the correct name) turret and it's sure a vast improvement in many ways compared to the earlier turret. Works real slick other then this small 204 problem.
Pydpiper, if you're interested in the type press I'm talking about and would like to learn how the turrets operate, there's an interesting writeup here with many good pics: http://www.realguns.com/archives/122.htm I might add I have no connection to Lee, in fact I've cussed their stuff a time or two.
![wink :wink:](./images/smilies/wink.gif)