Queston about a load and Chrono speeds

Share information about reloading the 204 Ruger.
CooperRandall
New Member
Posts: 17
Joined: Sat Feb 23, 2008 9:22 pm
.204 Ruger Guns: Cooper Phoenix - DTECH AR15

Queston about a load and Chrono speeds

Post by CooperRandall »

I am fairly new to reloading and I am finding it extremely fun. I am working on finding a good load for my DTECH AR 204. It has a 24" Shilen barrel with a 1 in 10" twist and so far I am extremely pleased.

I have gone through the following steps in my reloading process. Sized the brass - uniformed the primer pocket - de-burred the flash holes and chamfered the inside of the necks.

I am using Benchmark powder and 39 gr Blitzking bullets and Federal match primers.

I have sized the brass to 1.549" to the shoulder and the loaded rounds are 1.867 to the Ogive. There is so much freebore I can't get anywhere near the rifling and my magazine renders that as a no go anyway.

So I am pretty pleased with results and I found that the gun likes 25.1 grains and 25.5 grains of powder. The confusing part is that my Chronograph showed the following for the 25.1 grains loads.

low - 3320 fps
high - 3496 fps
Avg -3429 fps
spread - 176.4

group size for three three shot groups of this load were 0.413" - 0.395" - 0.204"

the conditions were not the greatest. Wind 20+ mph gusting out of the NE (I was shooting due south) and temp of 52 degrees.

I wouldn't figure the groups would be that good with the spread in velocities I was getting. Any ideas or thoughts? Pics below of some of my targets.

Image

Image

Image

Image
User avatar
Ahab
Junior Member
Posts: 74
Joined: Sun Mar 04, 2007 10:15 am
.204 Ruger Guns: T/C Contender Hvy. barrel, Savage 112
Location: Oracle, Az.

Re: Queston about a load and Chrono speeds

Post by Ahab »

I'm thinking that's not too bad of a spread for a gas operated semi-auto and the groups aren't that bad either. :)
NRA Endowment
Arizona Antelope Foundation
Arizona Desert Bighorn Sheep Society
WHISTLEPIG
Senior Member
Posts: 281
Joined: Sat Feb 18, 2006 8:09 am
Location: s. w. Idaho

Re: Queston about a load and Chrono speeds

Post by WHISTLEPIG »

Try moving your chrono out further. If you are setting it to 10 ft. go to 12 ft.
User avatar
glenn asher
Senior Member
Posts: 840
Joined: Wed Feb 09, 2005 6:25 pm
.204 Ruger Guns: Savage 12fvss, CZ 527 American
Location: kentucky
Contact:

Re: Queston about a load and Chrono speeds

Post by glenn asher »

I think I'd try H4895, too, while your groups are good, the velocity is pretty low compared to what you can achieve with 4895, and accuracy is usually pretty good with it. If you can get more speed AND accuracy, why not go for it?
Build a man a fire, and he's warm for a day. Set a man on fire and he's warm for the rest of his life!
CooperRandall
New Member
Posts: 17
Joined: Sat Feb 23, 2008 9:22 pm
.204 Ruger Guns: Cooper Phoenix - DTECH AR15

Re: Queston about a load and Chrono speeds

Post by CooperRandall »

I read that if you are getting consistent or small groups but a large spread in velocity a primer change might help. The info came from Hogdon's reloading magazine.
joghotrod
Senior Member
Posts: 124
Joined: Thu Sep 14, 2006 8:34 pm
Location: Baton Rouge Area

Re: Queston about a load and Chrono speeds

Post by joghotrod »

Hi Cooper,

I have 2 Dtech .204's and I use 27.5 grs. of H-4895 behind 39 SBK's and get around 3800 fps out of both of them. When I shoot 50 gr. Bergers out of the 1/9 twist it will be around 3400 fps. I use Varget with the Bergers. I shoot 39's at mag length and they work pretty good. :D

Jimmy
.204 Ruger M77 Mark II Weaver 6-24
.222 Rem. BDL Varmint Leupold VX III 6.5-20
.204 Dtech AR 24 in. 1/9 twist SS Fluted Shilen Barrel with Compensator, Leatherwood 8.5-25 uni-dial Also 1/12 twist Shilen. NRA Life Member
6BR Dtech Upper, Shilen 1/8 twist.
CooperRandall
New Member
Posts: 17
Joined: Sat Feb 23, 2008 9:22 pm
.204 Ruger Guns: Cooper Phoenix - DTECH AR15

Re: Queston about a load and Chrono speeds

Post by CooperRandall »

H-4895 it is. I will pick some up tomorrow. Thanks for the help. Would you stay with the Fed205m primers or try something else?
joghotrod
Senior Member
Posts: 124
Joined: Thu Sep 14, 2006 8:34 pm
Location: Baton Rouge Area

Re: Queston about a load and Chrono speeds

Post by joghotrod »

I use BR-4 primers but the 205's are probably ok.

Jimmy
.204 Ruger M77 Mark II Weaver 6-24
.222 Rem. BDL Varmint Leupold VX III 6.5-20
.204 Dtech AR 24 in. 1/9 twist SS Fluted Shilen Barrel with Compensator, Leatherwood 8.5-25 uni-dial Also 1/12 twist Shilen. NRA Life Member
6BR Dtech Upper, Shilen 1/8 twist.
User avatar
jo191145
Senior Member
Posts: 1064
Joined: Sun Sep 25, 2005 7:23 pm
Location: Central CT.

Re: Queston about a load and Chrono speeds

Post by jo191145 »

Coop
Don't know diddly about gas guns but make sure you edit your first cold clean shot from the chrono. Its usually quite slow. Not sure if this applies in your case but I figured I'd throw it out there.
Image

Image
Savage VLP + NF 12x42 + 35 Bergers = .
Post Reply