Norma brass Range report

Share information about reloading the 204 Ruger.
pathmaker
New Member
Posts: 19
Joined: Sun Jun 17, 2007 7:27 pm
Location: midwest

Post by pathmaker »

Great consistancy Hawkeye .I'll bet your runout is nil it would be interesting to know also the neck wall thickness.It must be the Redding Comp. dies and Norma brass now you got me thinking :shock:
Hawkeye Joe
Senior Member
Posts: 737
Joined: Tue Aug 08, 2006 4:42 pm
Location: Pendleton,New York

Post by Hawkeye Joe »

Wall thickness is still within .0002 after two firings.
Hawkeye Joe (Mike)
Savage model 10 Predator, 3-9 Nikon Omega
07 LRPV, 35X45 Leupold Competition
Image

Image
skipper
Moderator
Posts: 1404
Joined: Thu Feb 09, 2006 3:32 am
.204 Ruger Guns: Remington XR 100, Custom build Lilja/Panda/Shehane/Jewell
Location: Cypress, TX

Post by skipper »

Hawkeye Joe

Did you misplace a digit? Neck thickness of .0002 isn't possible, is it? By the way, that's some serious groups at 300 yards. Whatever you're doing, you're doing it right. Nice going. You're going to give me a run for the money with a factory rifle. Your bench technique must be very good. Do you dope the wind or just wait for the conditions to settle down, like me?
Image Hold 'em & Squeeze 'em
acloco
Senior Member
Posts: 1708
Joined: Mon Sep 25, 2006 8:53 pm
.204 Ruger Guns: 12FV, 12BVSS -S
Location: Nebraska

Post by acloco »

Hawkeye Joe wrote:acloco
If it's within .03 grains ,That's accurate...My Hornady would float .10 . I use a tolerance of +- .02 for my loads with the Acculab.How repeatable is it under loading conditions.About 3-4 loads per minute??
Don't know yet..letting the scale "burn in" for 48 hours or so.

Have been cleaning the garage...it is UGHHHLLY! My reloading bench & cleaning bench is in there...along with a radial arm saw, table saw, and, and, and.....oh...a complete engine (in pieces) for my 1965 Olds 442.

Been busy since the 1st of the year...seems busier than normal...so...little things get set here and there for "later"...and later never came. So....guess who gets to clean up? ....yep...me..the person that made the mess.

Promised myself when this scale arrived, I would do a good deeeeep clean. About halfway done.

Garage is not the bad....but it is bad to me...so that is what counts. :)
User avatar
Silverfox
Senior Member
Posts: 937
Joined: Tue Feb 01, 2005 1:51 pm
.204 Ruger Guns: Savage 12VLP purchased in June 2004 + 2 other custom .204s
Location: NW North Dakota

Post by Silverfox »

skipper--Read his sentence again--
Wall thickness is still within .0002 after two firings.
He didn't say that the neck walls were .0002" thick, he said "Wall thickness is still within .0002 after two firings." That means that the neck walls DO NOT vary more than .0002" in thickness after firing them twice. It DOES NOT mean that the neck walls are .0002" thick.

Maybe I made that as clear as mud :eek: :wink: :eek:
Catch ya L8R--Silverfox
Lee C.
Senior Member
Posts: 356
Joined: Fri Apr 21, 2006 12:00 am
Location: antigo wisconsin
Contact:

Post by Lee C. »

Great shooting Mike, Your skills s for reloading and shooting are starting to shine through now. ( nice going ) And if you ever get a picture of Rick shooting a savage. I would almost pay to see that on the forum here. :lol: Way to go mike
Hawkeye Joe
Senior Member
Posts: 737
Joined: Tue Aug 08, 2006 4:42 pm
Location: Pendleton,New York

Post by Hawkeye Joe »

Neck walls measure .011-.0112. Silverfox is correct. I forgot not everybody has been a Machinist for 25 years like me :oops:. I should have been more clear!


Skipper
My bench technique is kinda rough.I hold the gun with two hands :oops: As far as the wind goes,I shoot between gusts. My range is protected from cross winds except for opening in the trees between 200-250.With the addition of the Norma brass I believe I now have the "total package".
Image

Acloco
Under loading conditions mine is on the money almost every time.Once in a while it floats .02. just rezero and have at it! 65 Olds 442 SWEEEET.What engine, a 400ci ?. Original numbers matching??
Last edited by Hawkeye Joe on Sat Jul 07, 2007 5:15 am, edited 1 time in total.
Hawkeye Joe (Mike)
Savage model 10 Predator, 3-9 Nikon Omega
07 LRPV, 35X45 Leupold Competition
Image

Image
skipper
Moderator
Posts: 1404
Joined: Thu Feb 09, 2006 3:32 am
.204 Ruger Guns: Remington XR 100, Custom build Lilja/Panda/Shehane/Jewell
Location: Cypress, TX

Post by skipper »

My bad. I mistook what you wrote. I had to scratch my head twice on that one. :duh:
Image Hold 'em & Squeeze 'em
acloco
Senior Member
Posts: 1708
Joined: Mon Sep 25, 2006 8:53 pm
.204 Ruger Guns: 12FV, 12BVSS -S
Location: Nebraska

Post by acloco »

(Hawkeye Joe)....65 Olds 442 SWEEEET.What engine, a 400ci ?. Original numbers matching??
400 cubes = yes! Numbers match = yes!
Hawkeye Joe
Senior Member
Posts: 737
Joined: Tue Aug 08, 2006 4:42 pm
Location: Pendleton,New York

Post by Hawkeye Joe »

Went to the range today to Crony my favorite loads for the LRPV. It was very windy but I managed to get a couple of nice groups in early. The left target was shot with 25.3 10X,39gr Sierra BK,CCI BR4,OAL 2.260. 3 of 10 missed the paper. Notice the point of impact difference compared to the 35 Bergers on the right. Both are 300 yard targets. 35gr Berger load is 26.6 Benchmark. Now lets get to the Crono stuff. Here are the velocities of the 39 Sierra 25.3 10X loads:
3853 FPS
3842 FPS
3853 FPS
3842 FPS
3842 FPS
3842 FPS
3831 FPS
3842 FPS
3842 FPS
3809 FPS


Here are the 35 gr Bergs 26.6 Benchmark loads
3842 FPS
3853 FPS
3853 FPS
3820 FPS
3798 FPS
3831 FPS
3853 FPS
3875 FPS
3831 FPS
3887 FPS
It's funny that both loads the rifle likes are so similar.
Image
Hawkeye Joe (Mike)
Savage model 10 Predator, 3-9 Nikon Omega
07 LRPV, 35X45 Leupold Competition
Image

Image
User avatar
Hotshot
Senior Member
Posts: 809
Joined: Wed Apr 04, 2007 2:32 pm
.204 Ruger Guns: Savage and ar-15
Location: Rapid City
Contact:

Post by Hotshot »

acloco, enough about groups and prairie dogs. I want pictures of the 442. I've owned 5 over the years and a 65 was my first car out of high school. I'd trade all my Savages for a good builder.
acloco
Senior Member
Posts: 1708
Joined: Mon Sep 25, 2006 8:53 pm
.204 Ruger Guns: 12FV, 12BVSS -S
Location: Nebraska

Post by acloco »

HotShot - meet me in Shelby...on Saturday, Sunday or the rest of next week.

Was found in the proverbial "farmer's yard" south of Havre. Last licensed in 1968 and has just over 21K miles. Needs a complete interior. NO rust. Dented front fender and bumper.

One of few produced...it is a "F85 Club Coupe" with 442 option.
http://www.442.com/tech/442figs.html

Engine was ran hard or low on oil - ruined a connecting rod and scuffed one cylinder. I have another nodular crank and a set of rods (also 1965). But, you have a choice - sleeve this block or bore to 425 cube size - uses the same block as the 425. The cylinders are EASILY 3/8-7/16" inch thick - no bull.

Cam looks new - still has the gray/black coating. Heads are in perfect condition.
acloco
Senior Member
Posts: 1708
Joined: Mon Sep 25, 2006 8:53 pm
.204 Ruger Guns: 12FV, 12BVSS -S
Location: Nebraska

Post by acloco »

PS - car is worth 6-8K, even in the condition it is in (not bad, really).

Heads are worth a grand. Block/crank/Rods - worth close to a grand. 442 emblem on the dash is worth a grand.

Reallistically, to finish the car..figure:

3-5K for paint (medium metallic blue with white top)
$1300 for interior
2K for engine/tires/etc...

Last one that was in a GOOD restored condition, that I saw....went for 30K plus.

PS..sorry to hijack the thread!
Last edited by acloco on Mon Jul 09, 2007 9:20 am, edited 1 time in total.
trevort
Junior Member
Posts: 98
Joined: Fri Nov 11, 2005 5:01 am
.204 Ruger Guns: stiller predator, lilja no 5 1 in 12
Location: Melbourne Australia

Post by trevort »

Impressive shooting.

I've just been convinced to enter a 300 yd Fly comp, and I have no 204 at the moment!

But glad to hear the Norma brass is worth it. Just finishing uniforming the pockets on some 22/250 before necking up for my 6/250 and will then get on to the 200 204 cases in anticipation of the new 204s arriving!!!
Hawkeye Joe
Senior Member
Posts: 737
Joined: Tue Aug 08, 2006 4:42 pm
Location: Pendleton,New York

Post by Hawkeye Joe »

I don't mind a little car-jacking of my post 8) Here's My 72 Riviera GS doing a little smoke show.No brakes needed to heat em up with a 550+HP 455 Stage 1. It's the only heat show picture I have :oops: .And to top it off,It's my good bud driving :eek: I'm working the camera :D
Image
Hawkeye Joe (Mike)
Savage model 10 Predator, 3-9 Nikon Omega
07 LRPV, 35X45 Leupold Competition
Image

Image
Post Reply