BR PIVOT
BR PIVOT
I have a Br Pivot with the plastic top and made a wood top out of 3/4 Birch Plywood.. I have the dimensions, but need to know where to drill the hole for the center post assy... I guess I didn't drill the 1st one in the right place...
-
Mike
- Senior Member
- Posts: 676
- Joined: Mon Jan 02, 2006 4:05 pm
- .204 Ruger Guns: Cooper, RRA
- Location: Springfield, MO
Re: BR PIVOT
Denio, please tell me which measurements you need and I'll be happy to take them from my wood top.
Re: BR PIVOT
Mike, I just need the distance from the front edge of the top to where the 1st holes are drilled, and then from the holes to the right edge...
I drilled mine too close to the front... just doesn't feel right... Thanks...
I drilled mine too close to the front... just doesn't feel right... Thanks...
Re: BR PIVOT
I just need one hole (same one) measured to the front edge and then to the right edge...
-
Mike
- Senior Member
- Posts: 676
- Joined: Mon Jan 02, 2006 4:05 pm
- .204 Ruger Guns: Cooper, RRA
- Location: Springfield, MO
Re: BR PIVOT
Sorry for the delayed response, Denio. I'll take those measurements this evening for you.
-
Mike
- Senior Member
- Posts: 676
- Joined: Mon Jan 02, 2006 4:05 pm
- .204 Ruger Guns: Cooper, RRA
- Location: Springfield, MO
Re: BR PIVOT
Here are some pictures that I hope will help. All are taken with the bottom of the table facing up.
http://flic.kr/p/eJQmMr
From left edge of the table:
From right edge of the table:
From front edge of the table:
Width of mounting plate (left to right):
Length of mounting plate (front to back):
If you need any other shots or have questions about the ones I posted, please let me know.
Mike
http://flic.kr/p/eJQmMr
From left edge of the table:
From right edge of the table:
From front edge of the table:
Width of mounting plate (left to right):
Length of mounting plate (front to back):
If you need any other shots or have questions about the ones I posted, please let me know.
Mike
-
Mike
- Senior Member
- Posts: 676
- Joined: Mon Jan 02, 2006 4:05 pm
- .204 Ruger Guns: Cooper, RRA
- Location: Springfield, MO
Re: BR PIVOT
Here are some pictures that I hope will help. All are taken with the bottom of the table facing up.
From left edge of the table:
http://www.flickr.com/photos/92543431@N02/9017342137/
From right edge of the table:
http://www.flickr.com/photos/92543431@N02/9017348761
From front edge of the table:
http://www.flickr.com/photos/92543431@N02/9018523316
Width of mounting plate (left to right):
http://www.flickr.com/photos/92543431@N02/9017366107
Length of mounting plate (front to back):
http://www.flickr.com/photos/92543431@N02/9017362661
If you need any other shots or have questions about the ones I posted, please let me know.
Mike
From left edge of the table:
http://www.flickr.com/photos/92543431@N02/9017342137/
From right edge of the table:
http://www.flickr.com/photos/92543431@N02/9017348761
From front edge of the table:
http://www.flickr.com/photos/92543431@N02/9018523316
Width of mounting plate (left to right):
http://www.flickr.com/photos/92543431@N02/9017366107
Length of mounting plate (front to back):
http://www.flickr.com/photos/92543431@N02/9017362661
If you need any other shots or have questions about the ones I posted, please let me know.
Mike
Re: BR PIVOT
Thanks Mike... I was off a little... Extra holes drilled into the top will give it a little patina..
$170.00 plus shipping for a new one was a good reason to build my own... Thanks again... Jim
$170.00 plus shipping for a new one was a good reason to build my own... Thanks again... Jim
-
Mike
- Senior Member
- Posts: 676
- Joined: Mon Jan 02, 2006 4:05 pm
- .204 Ruger Guns: Cooper, RRA
- Location: Springfield, MO
Re: BR PIVOT
My pleasure, Jim.