BR PIVOT

General discussion and information about the 204 Ruger.
Denio
New Member
Posts: 34
Joined: Tue Apr 20, 2010 6:57 am
.204 Ruger Guns: Cooper 21 Phoenix

BR PIVOT

Post by Denio »

I have a Br Pivot with the plastic top and made a wood top out of 3/4 Birch Plywood.. I have the dimensions, but need to know where to drill the hole for the center post assy... I guess I didn't drill the 1st one in the right place...
Mike
Senior Member
Posts: 676
Joined: Mon Jan 02, 2006 4:05 pm
.204 Ruger Guns: Cooper, RRA
Location: Springfield, MO

Re: BR PIVOT

Post by Mike »

Denio, please tell me which measurements you need and I'll be happy to take them from my wood top.
Denio
New Member
Posts: 34
Joined: Tue Apr 20, 2010 6:57 am
.204 Ruger Guns: Cooper 21 Phoenix

Re: BR PIVOT

Post by Denio »

Mike, I just need the distance from the front edge of the top to where the 1st holes are drilled, and then from the holes to the right edge...
I drilled mine too close to the front... just doesn't feel right... Thanks...
Denio
New Member
Posts: 34
Joined: Tue Apr 20, 2010 6:57 am
.204 Ruger Guns: Cooper 21 Phoenix

Re: BR PIVOT

Post by Denio »

I just need one hole (same one) measured to the front edge and then to the right edge...
Mike
Senior Member
Posts: 676
Joined: Mon Jan 02, 2006 4:05 pm
.204 Ruger Guns: Cooper, RRA
Location: Springfield, MO

Re: BR PIVOT

Post by Mike »

Sorry for the delayed response, Denio. I'll take those measurements this evening for you.
Mike
Senior Member
Posts: 676
Joined: Mon Jan 02, 2006 4:05 pm
.204 Ruger Guns: Cooper, RRA
Location: Springfield, MO

Re: BR PIVOT

Post by Mike »

Here are some pictures that I hope will help. All are taken with the bottom of the table facing up.

http://flic.kr/p/eJQmMr


From left edge of the table:
Image

From right edge of the table:
Image

From front edge of the table:
Image

Width of mounting plate (left to right):
Image

Length of mounting plate (front to back):
Image

If you need any other shots or have questions about the ones I posted, please let me know.

Mike
Mike
Senior Member
Posts: 676
Joined: Mon Jan 02, 2006 4:05 pm
.204 Ruger Guns: Cooper, RRA
Location: Springfield, MO

Re: BR PIVOT

Post by Mike »

Here are some pictures that I hope will help. All are taken with the bottom of the table facing up.


From left edge of the table:
Image
http://www.flickr.com/photos/92543431@N02/9017342137/

From right edge of the table:
Image
http://www.flickr.com/photos/92543431@N02/9017348761

From front edge of the table:
Image
http://www.flickr.com/photos/92543431@N02/9018523316

Width of mounting plate (left to right):
Image
http://www.flickr.com/photos/92543431@N02/9017366107

Length of mounting plate (front to back):
Image
http://www.flickr.com/photos/92543431@N02/9017362661

If you need any other shots or have questions about the ones I posted, please let me know.

Mike
Denio
New Member
Posts: 34
Joined: Tue Apr 20, 2010 6:57 am
.204 Ruger Guns: Cooper 21 Phoenix

Re: BR PIVOT

Post by Denio »

Thanks Mike... I was off a little... Extra holes drilled into the top will give it a little patina..
$170.00 plus shipping for a new one was a good reason to build my own... Thanks again... Jim
Mike
Senior Member
Posts: 676
Joined: Mon Jan 02, 2006 4:05 pm
.204 Ruger Guns: Cooper, RRA
Location: Springfield, MO

Re: BR PIVOT

Post by Mike »

My pleasure, Jim.
Post Reply