Cleaning problem

General discussion and information about the 204 Ruger.
Big Deezul
New Member
Posts: 9
Joined: Sat Nov 10, 2007 3:29 pm
.204 Ruger Guns: Kimber pro varmint

Cleaning problem

Post by Big Deezul »

I bought a cleaning kit that my gun shop told me would work on my .204 barrel. I went to run the copper brush down the barrel and got about 1.5 inches in the barrel and realized it was too tight. Rather the jamming it down the barrel, I backed it out.....did I mess up anything?

Do you guys have a cleaning kit you recommend?
Ryan S Albright
Senior Member
Posts: 578
Joined: Sun Jul 02, 2006 8:59 pm
.204 Ruger Guns: Ruger 204 Ultra Light, Ruger 204 Standard, Ruger Target Gray
Location: Hemet California

Re: Cleaning problem

Post by Ryan S Albright »

I use a solid steel one piece nylon coated rod by Kleenbore they sell for under $10 dollars then buy a bore guide because it can take some push to get the brush down the barrel the first time. I don't think you hurt your barrel any they are made of tough steel. I do believe in using the wire brush though to keep the rifling groves cleaned out.
Phasor
New Member
Posts: 26
Joined: Tue Nov 29, 2005 4:29 pm
.204 Ruger Guns: Cooper Phoenix
Location: Cheyenne, Wyoming

Re: Cleaning problem

Post by Phasor »

While it is not advisable to reverse direction in the bore with a cleaning brush, you are lucky that you got it out. I use a Lucas bore guide and Boretech cleaning rod and that combo works great. The Boretech Elimator solvent is also good, as well as Wipeout and Patchout products. I believe that you can find the rods and brushes at Midway and other online dealers. The Lucas bore guide can be purchased directly from Lucas at the following address.

Mike Lucas
phone: (803) 356-0282 (7 days a week, 8am to 8pm EST)
225 Browns River Road
Lexington, SC 29072
email: lucasmjb@nuvox.net


Hope this helps,

Phasor
Big Deezul
New Member
Posts: 9
Joined: Sat Nov 10, 2007 3:29 pm
.204 Ruger Guns: Kimber pro varmint

Re: Cleaning problem

Post by Big Deezul »

the kit said it was for 22 cal should I use a 17?? I just e-mailed about the bore guide. I am not going to use the rifle again until I get a good cleaning set up
nzs204
New Member
Posts: 14
Joined: Mon Feb 12, 2007 6:24 pm
Location: new zealand

Re: Cleaning problem

Post by nzs204 »

you need a .20 cal cleaning kit. a .22 kit will not work. they are different.
.204 = 20 cal. not .22 good luck =)
Big Deezul
New Member
Posts: 9
Joined: Sat Nov 10, 2007 3:29 pm
.204 Ruger Guns: Kimber pro varmint

Re: Cleaning problem

Post by Big Deezul »

nzs204 wrote:you need a .20 cal cleaning kit. a .22 kit will not work. they are different.
.204 = 20 cal. not .22 good luck =)
Thats why it got stuck :wall:

thank you
nzs204
New Member
Posts: 14
Joined: Mon Feb 12, 2007 6:24 pm
Location: new zealand

Re: Cleaning problem

Post by nzs204 »

im actually surpised you managed to get it into your barrel at all! good job on that! ;)
anyway i doubt you would have damaged your barrel, just reframe from doing it again =p
Big Deezul
New Member
Posts: 9
Joined: Sat Nov 10, 2007 3:29 pm
.204 Ruger Guns: Kimber pro varmint

Re: Cleaning problem

Post by Big Deezul »

will do. I found some cleaning kits for the .204 I am going to pick one up tomorrow. I will wait for my bore guide to clean it though
skipper
Moderator
Posts: 1404
Joined: Thu Feb 09, 2006 3:32 am
.204 Ruger Guns: Remington XR 100, Custom build Lilja/Panda/Shehane/Jewell
Location: Cypress, TX

Re: Cleaning problem

Post by skipper »

I use a Dewey cleaning rod and a Lucas Bore guide. Dewey makes caliber specific cleaning rods and Mike Lucas fits his inserts to the cleaning rod diameter. This combination gives me the best insurance from damaging my bore with improper cleaning techniques and equipment. You will need to make sure you have a cleaning rod long enough to clear the end of the barrel with the bore guide in place. I use a 38 inch cleaning rod with a 26 inch barrel and guide.

Dewey also makes a "No Harm" 20 caliber brass brush. Buy about a dozen of them. They will reverse in the bore.
http://www.midwayusa.com/eproductpage.e ... t=11082005

Here is a picture of my custom Stolle Panda getting a thorough scrubbing.

Image

Image
Image Hold 'em & Squeeze 'em
Big Deezul
New Member
Posts: 9
Joined: Sat Nov 10, 2007 3:29 pm
.204 Ruger Guns: Kimber pro varmint

Re: Cleaning problem

Post by Big Deezul »

I talked to Mike this morning and ordered bore guides for a few of my rifles. I like the dewey rods, I may order them today. I wonder if Bass pro or Gander mountain would have them in stock
Phasor
New Member
Posts: 26
Joined: Tue Nov 29, 2005 4:29 pm
.204 Ruger Guns: Cooper Phoenix
Location: Cheyenne, Wyoming

Re: Cleaning problem

Post by Phasor »

If you are looking for the Dewey, you can get it here:

http://www.midwayusa.com/eproductpage.e ... t=11082005

Phasor
Big Deezul
New Member
Posts: 9
Joined: Sat Nov 10, 2007 3:29 pm
.204 Ruger Guns: Kimber pro varmint

Re: Cleaning problem

Post by Big Deezul »

Phasor wrote:If you are looking for the Dewey, you can get it here:

http://www.midwayusa.com/eproductpage.e ... t=11082005

Phasor
thanks...I was surprised to see them in stock at my local gun shop so I picked them up today. One for each of my rifles and the correct size brushes and jags
GlennGTR
New Member
Posts: 37
Joined: Fri Nov 16, 2007 9:32 pm
.204 Ruger Guns: 77 ultralight all weather

Re: Cleaning problem

Post by GlennGTR »

I use the otis cleaning kit.a good bore cleaner such as kleen bore and a conditioner usualy break free. I prefer pulling the brush and patches from breach to bore.Way faster then removing the brush tip every time.I have been using the 22 call brush myself with good results.The cable allows me to pull a very tight patch through that i couldnt do with a rod.Cleaner gun less time cleaning got to love that.
Post Reply