Keeping brass bright

Ask questions and share information about reloading.
hogan
New Member
Posts: 15
Joined: Wed Aug 16, 2017 10:46 am
.204 Ruger Guns: Mossberg MVP predator
Location: Wisconsin

Keeping brass bright

Post by hogan »

First off, I am anal about clean brass.
After tumbling my brass in lemishine and SS my brass looks great but it does not take long for that shine to fade.
Anybody have any suggestions on keeping the brass shiny?
User avatar
Rick in Oregon
Moderator
Posts: 4942
Joined: Thu Dec 01, 2005 4:20 pm
.204 Ruger Guns: Sako 75V, Cooper MTV, Kimber 84M, Cust M700 11 Twist
Location: High Desert of Central Oregon
Contact:

Re: Keeping brass bright

Post by Rick in Oregon »

Everyone has their own regimen in regard to their personal beloved brass, myself included. Anal, yes, but if we're into this pastime, it's pretty much assured you're anal about it. (Or should be. :D )

Probably not the panacea, but I just store all my brass in hinged plastic 100 cnt Berry's Boxes, shoot, put back into the case, and upon returning home the brass goes immediately into my vibratory case cleaner. I do not handle it after it's been loaded, so no fingerprints or contaminants. I have loaded rounds from a few seasons ago for some rifles that never got shot, and the brass all looks like it was loaded last week. All my ammo is stored in military .50 cal cans, air and watertight....maybe that makes a difference, dunno.

Moisture, humidity, and general exposure to the air will tarnish brass, but if it's clean to start with and stored in airtight containers, it should in theory stay shiny for a very long time. I live in an arid desert environment with very low humidity, so that I'm sure is a contributing factor to why my brass stays so shiny for so long.

I'm sure others will chime in with their methods. I'm always interested in hearing what others do.
Semper Fortis
Rick in Oregon
NRA Life/OHA/VHA/VVA

Oregon, East of the Cascades - Where Common Sense Still Prevails

Image
MZ5
Senior Member
Posts: 106
Joined: Sat Oct 13, 2007 2:57 pm
.204 Ruger Guns: Ruger M77 Hawkeye Predator
Location: Arizona, USA

Re: Keeping brass bright

Post by MZ5 »

The only issue I’ve ever had with ss pin tumbled brass tarnishing is when I haven’t got the acid (lemi-shine) rinsed off completely. Maybe slower drying time exacerbates that.
User avatar
BitterClinger
New Member
Posts: 30
Joined: Tue Feb 20, 2018 8:36 pm
.204 Ruger Guns: Savage M12 LRPV

Re: Keeping brass bright

Post by BitterClinger »

If you want to keep that bright shine longer you have to protect the brass from oxygen. After wet cleaning my brass I let it dry and then dry tumble in corncob with some Turtle Wax All Metal Polish drizzled in. The Turtle Wax polish will help keep that shine as it helps to slow the oxidation . Just never use Brasso or other polishes that contain ammonia as it attacks the brass.
skipper
Moderator
Posts: 1404
Joined: Thu Feb 09, 2006 3:32 am
.204 Ruger Guns: Remington XR 100, Custom build Lilja/Panda/Shehane/Jewell
Location: Cypress, TX

Re: Keeping brass bright

Post by skipper »

Polished lots of brass as a Drill Instructor in the Marines. Best trick I've ever seen is to use Ronson's lighter fluid on a clean white cloth after tumbling. You'll see why immediately after the first case. Move to a clean area of the cloth when the black residue starts to build. Then don't touch it. It'll stay shiny almost forever.
Image Hold 'em & Squeeze 'em
Bill K
Senior Member
Posts: 2324
Joined: Tue Jan 18, 2011 10:00 am
.204 Ruger Guns: also now, a Savage switch bull barrel in 204R. 23 inch SS
Location: Lake Forest, Ca.

Re: Keeping brass bright

Post by Bill K »

The old Ronson trick and remember Jon'e hand warmer fluid works as well. Bill K
User avatar
BitterClinger
New Member
Posts: 30
Joined: Tue Feb 20, 2018 8:36 pm
.204 Ruger Guns: Savage M12 LRPV

Re: Keeping brass bright

Post by BitterClinger »

While lighter fluid may very well shine and protect brass and is fine for the type of brass on a uniform, it is highly inadvisable to use any petroleum products on brass ammo casings for obvious reasons.
Bill K
Senior Member
Posts: 2324
Joined: Tue Jan 18, 2011 10:00 am
.204 Ruger Guns: also now, a Savage switch bull barrel in 204R. 23 inch SS
Location: Lake Forest, Ca.

Re: Keeping brass bright

Post by Bill K »

And what are the obvious reasons ? It evaporates very quickly and causes no lasting effects. Just curious. Bill K
skipper
Moderator
Posts: 1404
Joined: Thu Feb 09, 2006 3:32 am
.204 Ruger Guns: Remington XR 100, Custom build Lilja/Panda/Shehane/Jewell
Location: Cypress, TX

Re: Keeping brass bright

Post by skipper »

I was not advocating that the lighter fluid goes inside the case, just on the outside. However I have put jewelers rouge into my media before with no ill results.
Image Hold 'em & Squeeze 'em
User avatar
Rick in Oregon
Moderator
Posts: 4942
Joined: Thu Dec 01, 2005 4:20 pm
.204 Ruger Guns: Sako 75V, Cooper MTV, Kimber 84M, Cust M700 11 Twist
Location: High Desert of Central Oregon
Contact:

Re: Keeping brass bright

Post by Rick in Oregon »

skipper wrote: Thu Sep 27, 2018 12:38 pmI have put jewelers rouge into my media before with no ill results.
Skipper, IRT jewelers rouge on rifle cases; I found some years ago that it builds up inside the case, and if not removed could/will eventually influence the interior volume of the case. And we all know that ain't good! :eek:

Just another one of those pearls of wisdom gained over decades of stuffing cases in the man cave. :wink: FWIW
Semper Fortis
Rick in Oregon
NRA Life/OHA/VHA/VVA

Oregon, East of the Cascades - Where Common Sense Still Prevails

Image
skipper
Moderator
Posts: 1404
Joined: Thu Feb 09, 2006 3:32 am
.204 Ruger Guns: Remington XR 100, Custom build Lilja/Panda/Shehane/Jewell
Location: Cypress, TX

Re: Keeping brass bright

Post by skipper »

I agree with your assessment, however people have been adding all sorts of things to media for years. Some manufacturers even add it themselves. Rouge, NuFinish, Turtle Wax, Ronson lighter fluid, etc. I think that as long as you clean your cases out afterwards everything will be okay. I usually run my cases through a brass brush attachment after tumbling anyhow. Tumbling never did much for the insides. I'm not the definitive expert on the subject. I do like my cases to be shiny though. I love my neck tension to be consistent, even more.
Image Hold 'em & Squeeze 'em
User avatar
Rick in Oregon
Moderator
Posts: 4942
Joined: Thu Dec 01, 2005 4:20 pm
.204 Ruger Guns: Sako 75V, Cooper MTV, Kimber 84M, Cust M700 11 Twist
Location: High Desert of Central Oregon
Contact:

Re: Keeping brass bright

Post by Rick in Oregon »

skipper wrote: Thu Sep 27, 2018 3:31 pmI do like my cases to be shiny though. I love my neck tension to be consistent, even more.
Yessir on both accounts! :D

I know you're as fussy as myself and figured you would never tolerate any foreign material in your cases. I just wanted to point out to others that the stuff can and will build up on the inside of rifle cases, and cause potential issues down the road. I quit putting rouge in my tumbling mix, just keep the stuff as clean as possible and change it out often.

Who doesn't love shiny cases? :wink:
Semper Fortis
Rick in Oregon
NRA Life/OHA/VHA/VVA

Oregon, East of the Cascades - Where Common Sense Still Prevails

Image
Post Reply